Dilution Ratio Liquid Measure Sq. Foot Coverage Glossary of Terms Floor Care Cost per RTU Wall Charts Food Service Guides Actiblend FAQ Actiblend Install/Troubleshooting Dual Draw FAQ Dual Draw Install/Troubleshooting Dispenser Manuals & Tip Charts

Company Directory Company Location Request an MSDS Online Career Opportunities

Installation & Troubleshooting for:

Dual Draw

Packing List:	Tools Needed For Installation:
One Dual Draw Dispenser One 6’ braided discharge hose with clamp Two clear chemical connector hoses Two chemical connector caps Two dilution tip kits with chart One bag of fasteners	One Dual Draw Dispenser One 6’ braided discharge hose with clamp Two clear chemical connector hoses Two chemical connector caps Two dilution tip kits with chart One bag of fasteners

Actiblend Dual Draw Installation Requirements:

Mount Dual Draw dispenser above chemical components to prevent siphoning of chemical.
Location should be an area with enough room to bring all cleaning equipment close to the Actiblend Dual Draw System.
Area should have a floor drain to ease dumping of dirty cleaning solution before filling cleaning equipment.
Dedicated water line with a garden hose connection with a minimum of 7gpm of flow

Step 1 – Mount unit to wall using hardware provided. Make sure unit is mounted above where containers will be placed

Step 2 – Facing the unit select & insert dilution tip into eductor on the left for component A . Connect chemical hose to eductor . Next, select and insert dilution tip into eductor on the right for component B. Connect chemical hose to eductor .

Step 3 – Connect discharge hose to dispenser using plastic clamp. IMPORTANT: make sure priming ring is 1 to 2 inches below dispenser in the hose.

Step 4 – Connect chemical hoses to connector caps (Trim excess hose if needed) Use radiator clamps to prevent air leaks.

Step 5 – Place pails of A&B components below dispenser and connect cap to pails tightly. Be sure to connect the proper cap to the correct component.

Step 6 – Connect incoming water line to garden hose fitting on dispenser.

Step 7 – Mount the hose hook to the left below the dispenser as you face the system.

Step 8 – Turn on water supply then turn operating ball valve to the ON position. Chemical should draw up both tubes and dispense RTU cleaner.

Step 9 – For drum installations follow the same procedures making sure the dispenser is above the top of the drums

Important Information

Operating Limits for all Actiblend Dual Draw System – Failure to adhere to these limits will result in liability for repairs

The Dual Draw System is designed for use with Actiblend Superconcentrate ONLY — Do not use any other products though the system.

Water Pressure - Operate Express units between 20psi and 70psi – higher line pressure will cause damage to internal parts & reduce dilution accuracy (40psi is optimal pressure).

Water Temperature – Operate Dual Draw unit in ambient temperatures not to exceed 100°F. Higher temperatures can damage internal parts.

Recommended Maintenance-In hard water areas Nuance recommends running a mild acid through the dispenser as needed to remove hard water build-up & scale deposits.

Never restrict flow at end of hose! If restricted, water will flow out the top of the vacuum breaker & hose could blow off spilling chemical on floor.

Troubleshooting Guide

Setup Problem	Cause	Possible solution
Chemical not drawing	Water pressure too low	Connect to water source with at least 7gpm of flow at 25 psi
	Water pressure too High	Connect to water source with at least 7gpm of flow below 70 psi or install pressure regulator
	Discharge hose connected at wrong end	Reconnect discharge hose with priming ring 3-5 inches from dispenser
	Caps not connected properly	Reconnect caps
	Air leak	Tighten cap and put radiator clamps on both ends of chemical tubes
Dilution to strong	Metering tip too large	Install smaller tip
Dilution to Weak	Metering tip too small	Install larger tip
Dual Draw system is sputtering/bubbles in the chemical tubes	Air leak	Tighten cap and put radiator clamps on both ends of chemical tubes
Unequal draw of the A&B	Slight variations in draw are to be expected but significant differences are due to incorrect tips	Replace with correct tip or increase or decrease tip size accordingly
Maintenance Issue	Cause	Possible solution
Dilution to Weak	Metering tips clogged	Remove, clean and re-install tips
	Hard water build up in venture	Remove dispenser from wall and clean venture with mild acid
Chemical not drawing	Hard water build up in venture	Remove dispenser from wall and clean venture with mild acid
	Metering tips clogged	Remove, clean and re-install tips
Chemical not primed in tubes	Cap check valve is damaged	Replace connector cap

If your question or concern was not addressed, please contact our Techinical Department at 773-928-2774

900 E. 103rd Street, Suite D, Chicago, Il 60628 1-800-621-8553